United States Stove DR6 Owner's Manual download pdf (Page 5)



Two basic types of chimneys are approved

for use with solid fuel: Factory-built and ma-

sonry. Factory-built chimney must comply

with UL 103 type “HT” standard.

Do not expect your stove or furnace to

create draft. Draft is not a function of the

appliance. It is purely a function of the

chimney. Modern stoves and furnaces

are much more air-tight and efcient

than those of the past and, therefore re-

quire greater draft. A minimum of .05 w.c.

(12.45Pa), is required for proper drafting

to prevent back-pufng, smoke spillage,

and to maximize performance. Gauges to

measure chimney draft are readily avail-

able at stove shops and are economical

to purchase or rent.

Chimneys perform two functions - one of

which is apparent: The chimney provides

a means for exhausting smoke and ue

gases resulting from combustion of the fuel.

Secondarily, though, the chimney provides

“Draft” which allows oxygen to be continu-

ously introduced into the appliance, so that

proper combustion is possible.



Your chimney connector and chimney must

have the same diameter as the stove outlet

(6”). If this is not the case, we recommend

you contact your dealer in order to insure

there will be no problem with the draft.

The stove pipe must be made of aluminized

or cold roll steel with a minimum thickness

of 0.021” or 0.53 mm. It is strictly forbidden

to use galvanized steel.

To Stove

Your smoke pipe should be assembled in

such a way that the male section (crimped

end) of the pipe faces down. This will allow

condensation in the ue to run back into the

heater. Attach each of the sections to one

another with three equidistant metal screws

and seal each joint with furnace cement.

The pipe must be short and straight. All

sections installed horizontally must slope at

least 1/4 inch per foot, with the upper end

of the section toward the chimney.

To insure a good draft, the total length of

the coupling pipe should never exceed 8’

to 10’ (2.4m to 3.04 m). (Except for cases

of vertical installation, cathedral-roof style

where the smoke exhaust system can

be much longer and connected without

problem to the chimney at the ceiling of

the room).

It is recommended that no more than two

90 degree bends be used because it may

reduce the amount of natural draft. The use

of corrugated (non-adjustable) elbows is

preferred as they are much more airtight.

You must have at least 18 inches of

clearance between any horizontal piping

and the ceiling.

The pipe cannot extend into the chimney

ue.

The chimney connector must not pass

through an attic, roof space, closet, any

concealed space, floor, ceiling, wall or

combustible construction. Where passage

through a wall or partition of combustible

construction, the installation must conform

to CAN/CSA-B365, Installation Code for

Solid-Fuel-Burning Appliances & Equipment.



   

1 67725P Panel, Cabinet Front - Pewter 1

2 23477 Shield, Top Thermo 1

3 67967B Cabinet, Left 1

4 67968B Frame, Door 1

5 67969B Door, Cabinet 1

6 89065 Hinge, Door 4

7 89635 Knob, Door 1

8 83093 Latch, Spring 1

9 83005 #10-24 x 1/2 Machine Screw, PH HD 2

10 69557B Back, Cabinet 1

11 21063 Brace, Back 2

12 67966B Top, Cabinet 1

13 21593 Support, Hinge 1

14 83833 Clip, Hinge 1

15 67743 Assy., Thermostat 1

16 69271 Chain & Hook Assembly 1

17 851886 Plate, Control Panel - Wonderluxe 1

18 89687 Knob, Thermostat 1

1 2 3 4 5 6 7 8 9 10 11 12

Comments to this Manuals

No comments

United States Stove DR6 Owner's Manual Page 5

Comments to this Manuals